Login/Register
Shopping Cart
OR
Filter
Sort By
Simpson Strong-Tie PDPAWL-150 Zinc Plated Pin is a powder-actuated washered pin designed to fasten building components to concrete, steel and CMU. The PDPAWL consists of a hardened-steel PDPA pin...
Simpson Strong-Tie PDPAWL-150 Zinc Plated Pin is a powder-actuated washered pin designed to fasten building components to concrete, steel and CMU. The PDPAWL consists of a hardened-steel PDPA pin preassembled with a 1″ washer that provides additional bearing surface for enhanced upload resistance. Length: 1-1/2" Head Diameter: .300" Shank Diameter: .157" Coating: Standard G90 Zinc PDPAWL Series Fasteners Tension and Shear Loads in Normal Weight Concrete PAT Fastener MSDS Standard G90 Zinc...
The Simpson Strong-Tie Quik Drive® WSV2S #9 x 2" Screws are ideal for screwing wood-to-wood when their is little concern about corrosion of the fasteners. The most common use of these screws is...
The Simpson Strong-Tie Quik Drive® WSV2S #9 x 2" Screws are ideal for screwing wood-to-wood when their is little concern about corrosion of the fasteners. The most common use of these screws is for subfloor applications because the screw creates a very tight connection between the plywood and joist. Using a StrongDrive® Automatic Tool with a 20" extension saves time and labor thus saving you money. Redesigned tip and thread pattern provides easy starts and up to 25% less torque while...
The Simpson T15N150SFB 1-1/2" x 15ga. Angled Type 316 Stainless Steel Finish Nails should be used in exterior applications where highly corrosive conditions exist like seaside envoronments. The...
The Simpson T15N150SFB 1-1/2" x 15ga. Angled Type 316 Stainless Steel Finish Nails should be used in exterior applications where highly corrosive conditions exist like seaside envoronments. The D-style head has greater bearing area to draw trim to the substrate. DA Style Finish Nails Fit the Following Tools: (Please check your owners manual regarding the proper lengths that your tool can use) Senco: FinishPro42XP, FinishPro41XP, FinishPro35, SFN40, SFN30, SFN1, SFN2B, SN1...
The Simpson T9A150MCN 1-1/2" x .148" Type 316 Stainless Steel Metal Connector Nails is designed to be used in 31/33 Degree Metal Connector Tools for installing Simpson Strong-Tie structural...
The Simpson T9A150MCN 1-1/2" x .148" Type 316 Stainless Steel Metal Connector Nails is designed to be used in 31/33 Degree Metal Connector Tools for installing Simpson Strong-Tie structural connectors like clips, straps, joist hangers and more. Since the installation of this product is usually done close to the face these nails have a paper tape as opposed to plastic that breaks off and poses a hazard to the eyes and face. Please Note: Consult your manufacturer's catalog to determine the...
The Simpson Strong-Tie THD37300H4SS Type 304 Stainless Steel 3/8" x 3" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion...
The Simpson Strong-Tie THD37300H4SS Type 304 Stainless Steel 3/8" x 3" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the ideal anchor for structural applications, even at minimum edge distances and under reduced spacing conditions. The proprietary cutting teeth enable the Titen HD to be installed in one eighth of the time when compared to traditional expansion anchors, and at...
The Simpson Strong-Tie THDB25412CS 1/4" x 4-1/2" Titen HD heavy-duty screw anchor with countersunk head is part of a family of products that sets the standard for high-performance anchoring and ease...
The Simpson Strong-Tie THDB25412CS 1/4" x 4-1/2" Titen HD heavy-duty screw anchor with countersunk head is part of a family of products that sets the standard for high-performance anchoring and ease of installation. Designed for use in dry, interior, noncorrosive environments or temporary outdoor applications, the countersunk Titen HD offers industry-leading performance even in seismic conditions. The countersunk head style is for applications that require a flush-mount profile. Countersinking...
The Simpson Strong-Tie TNT18134TF Titen Turbo™ 3/16" x 1-3/4" 6-Lobe Flat Head Screw Anchor is fast and easy to install, and incredibly reliable in its performance. The secret behind the...
The Simpson Strong-Tie TNT18134TF Titen Turbo™ 3/16" x 1-3/4" 6-Lobe Flat Head Screw Anchor is fast and easy to install, and incredibly reliable in its performance. The secret behind the performance of the Titen Turbo™ lies in a thread design that lowers driving torque while providing superior holding power. The revolutionary Torque Reduction Channel between the threads gives drilling dust a place to go, thereby significantly reducing torque-related issues like binding, stripping...
The Intercorp Strong-Point 1-5/8" x #6 Black Phosphate Coarse Phillips Bugle Drywall Screws are a specialized type of fastener designed for attaching drywall (also known as gypsum board or...
The Intercorp Strong-Point 1-5/8" x #6 Black Phosphate Coarse Phillips Bugle Drywall Screws are a specialized type of fastener designed for attaching drywall (also known as gypsum board or sheetrock) to wood or steel framing during both residential and commercial construction. Drywall fasteners can also used for other applications, such as attaching drywall to furring strips and installing drywall to existing walls and ceilings during renovations. These drywall fasteners offer several design...
These 1/2" x 10" hex head plated machine bolts can be used for various wood-to-wood and/or metal-to-wood connection. Grade 2 ASTM A307 Zinc Plated Hex Head Uses 3/4" Socket Imported Thread Length...
These 1/2" x 10" hex head plated machine bolts can be used for various wood-to-wood and/or metal-to-wood connection. Grade 2 ASTM A307 Zinc Plated Hex Head Uses 3/4" Socket Imported Thread Length May Not Match Picture Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This coating provides a low level of corrosion resistance and should be used in dry environments. Level of Corrosion...
These 1/2" x 8" plated lag screws can be used for fastening metal-to-wood or wood-to-wood applications. Pre-drilling is required. Length is measured from the bottom of the hex head and may vary...
These 1/2" x 8" plated lag screws can be used for fastening metal-to-wood or wood-to-wood applications. Pre-drilling is required. Length is measured from the bottom of the hex head and may vary slightly. Zinc Plated Hex Head Imported Thread Length May Not Match Picture Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This coating provides a low level of corrosion resistance and...
3/4" - 10 Hot Dipped Galvanized Hex Nuts for either 3/4" HDG machine bolts or all thread rod. Uses 1-1/8" socket to install. Important: These HDG hex nuts will only fit hot galvanized bolts or...
3/4" - 10 Hot Dipped Galvanized Hex Nuts for either 3/4" HDG machine bolts or all thread rod. Uses 1-1/8" socket to install. Important: These HDG hex nuts will only fit hot galvanized bolts or threaded rod. Do NOT use on plain or zinc plated bolts. Hot Dipped Galvanized Coating Information Hot-Dip Galvanizing is applied after the products are fabricated. The coating weight increases with material thickness. The minimum average coating weight is 2.0 oz./ft2 (per ASTM A123 total both sides)....
3/4" Plain Malleable Cast Iron Round Washers are used in various types of wood construction. Malleable Iron Washers have a large bearing surface designed to prevent 3/4" bolt heads and nuts from...
3/4" Plain Malleable Cast Iron Round Washers are used in various types of wood construction. Malleable Iron Washers have a large bearing surface designed to prevent 3/4" bolt heads and nuts from pulling into the wood. These washers are not coated with any corrosion resistance material and will quickly rust if exposed to the elements. Bolt Hole Size: 13/16" Approximate Outside Diameter: 2-15/16" Approximate Washer Thickness: 3/8" Coating: None Explanation of "Stock" Availability Term Stock...
3/4" USS Zinc Plated Flat Washers are used to prevent the bolt head and/or hex nut from embedding into the wood surface during tightening. Zinc Plating provides minimum corrosion resistance and...
3/4" USS Zinc Plated Flat Washers are used to prevent the bolt head and/or hex nut from embedding into the wood surface during tightening. Zinc Plating provides minimum corrosion resistance and should not be used with ACQ lumber. Bolt Size: 3/4" Inside Diameter: 13/16" Outside Diameter: 2" Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This coating provides a low level of...
BP58-2HDG Hot Dipped Galvanized Square Bearing Plates give greater bearing surface than standard cut washers, and help distribute the load at these critical connections. These bearing plates are hot...
BP58-2HDG Hot Dipped Galvanized Square Bearing Plates give greater bearing surface than standard cut washers, and help distribute the load at these critical connections. These bearing plates are hot dipped galvanized to protect the washer from corrosion when exposed to the elements as well as coming in contact with ACQ lumber. Hole Size: 11/16" Dimension: 2" x 2" Thickness: 3/16" Coating: Hot Dipped Galvanized Mild Steel Imported Picture may not match product exactly Hot Dipped Galvanized...
These 5/8" x 12" hot dipped galvanized all thread rods when used with a 5/8" HDG coupling nut can be used for extending HDG machine bolts and HDG all thread rod. They can also sometimes be used as...
These 5/8" x 12" hot dipped galvanized all thread rods when used with a 5/8" HDG coupling nut can be used for extending HDG machine bolts and HDG all thread rod. They can also sometimes be used as an anchor bolt substitution (Consult your structural engineer first). Hot dipped galvanizing provides extra protection when contacting ACQ lumber. Please Note: This all thread is cut in our own shop. Bare ends are painted with galvanizing spray paint. A307 Grade 2 Hot Dipped Galvanized Special...
No Predrilling. Stronger than 3/8" Lags! The FMTLOK10 10" FastenMaster® TimberLok® Heavy Duty Wood Screw can replace 3/8" lag screws and enables you to complete wood-to-wood projects faster,...
No Predrilling. Stronger than 3/8" Lags! The FMTLOK10 10" FastenMaster® TimberLok® Heavy Duty Wood Screw can replace 3/8" lag screws and enables you to complete wood-to-wood projects faster, easier and stronger. All design values based on 1-1/2" side member thickness and penetration into main member as follows; TimberLok 2", Nails 10x diameter, Lags 8x diameter. Design values may be subject to adjustment factors (section 10.3 in NDS) based on conditions existing during installation as...