Login/Register
Shopping Cart
OR
Filter
Sort By
The Simpson Strong-Tie DTC Double Slotted Roof Truss Clips are used for alignment control between a roof truss and nonbearing walls. The DTC has two 1-1/2" slots that will permit the truss chord to...
The Simpson Strong-Tie DTC Double Slotted Roof Truss Clips are used for alignment control between a roof truss and nonbearing walls. The DTC has two 1-1/2" slots that will permit the truss chord to move vertically when loads are applied to the roof. The double slot increases the allowable load values. Material: 18 Gauge Finish: Standard G90 Zinc Fasteners: (6) 8d Nails DTC Information and Installation Instructions Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized...
The Simpson Strong-Tie H1AZ ZMax® Hurricane Tie provides a connection between the truss or rafter and the wall of the structure that helps resist wind and seismic forces. The H1AZ is designed...
The Simpson Strong-Tie H1AZ ZMax® Hurricane Tie provides a connection between the truss or rafter and the wall of the structure that helps resist wind and seismic forces. The H1AZ is designed for nominal 2x lumber. These U-shaped hurricane ties provide faster installation than using two single-sided ties. The embossments add stiffness in crucial areas for improved performance. Holds the rafter or truss on both sides for high lateral load resistance Can be installed on inside or outside of...
Simpson Strong-Tie HL33PC Powder Coat Heavy Angles can be used for connecting lumber at a 90° angle using either through bolts or lags. You can also use the HL33PC to connect lumber to concrete...
Simpson Strong-Tie HL33PC Powder Coat Heavy Angles can be used for connecting lumber at a 90° angle using either through bolts or lags. You can also use the HL33PC to connect lumber to concrete using an a wedge anchor or Titen Screw Bolt. Standard G90 Zinc Coating with a Black Powder Coat provides a low level of corrosion resistance. Material: 7 gauge Finish: Standard G90 Zinc Coating with a Black Powder Coat Dimensions: 3-1/4" (W1) x 3-1/4" (W2) x 2-1/2" (L) Bolt Holes: (2) 1/2" HL33PC...
The Simpson Strong-Tie L50 Reinforcing Angle are a 5" long framing clip used to create 90° wood to wood connections. The staggered nail pattern reduces the possibility of splitting the wood. The...
The Simpson Strong-Tie L50 Reinforcing Angle are a 5" long framing clip used to create 90° wood to wood connections. The staggered nail pattern reduces the possibility of splitting the wood. The flanges are 2-3/8" and 1-3/8" wide. The L50 angles can use 10d x 1-1/2" joist nail or #10 X 1-1/2" SD Structural Screws. Material: 16 Gauge Finish: Standard G90 Galvanized Length: 5" Flange Widths: 1-3/8" x 2-3/8" Fasteners: (6) 10d x 1-1/2" Nails or (6) SD #10 x 1-1/2" Screws L50 Information and...
The Simpson Strong-Tie LS50 Skewable Reinforcing Angles are field adjustable from 0° to 135°. These clips come standard with a 45° bend. The LS Skewable clips can only be bent one time....
The Simpson Strong-Tie LS50 Skewable Reinforcing Angles are field adjustable from 0° to 135°. These clips come standard with a 45° bend. The LS Skewable clips can only be bent one time. Flanges are 2-1/4" wide. LS50 Angles can use 10d .148" x 1-1/2" or longer nails depending on the application. Material: 18 Gauge Finish: Standard G90 Zinc Galvanizing Length: 4-7/8" Flange Widths: 2-1/4" x 2-1/4" Fasteners: (8) 10d x 1-1/2" Nails LS50 Information and Installation Instructions...
The Simpson Strong-Tie RTA12Z ZMax® Rigid Tie® is designed to connect two 1x2 or larger post and joist at a 90° angle. This rigid tie angle fastens the members on two sides, eliminating the...
The Simpson Strong-Tie RTA12Z ZMax® Rigid Tie® is designed to connect two 1x2 or larger post and joist at a 90° angle. This rigid tie angle fastens the members on two sides, eliminating the need for angle bracing. Manufactured to high-quality standards to ensure solid performance, this rigid tie connector features a ZMax® galvanized finish for added corrosion resistance. Ideal for gates, fences or any project where a 90® connection is needed Fastens with #8 x 3/4" Screws (not...
The Simpson Strong-Tie SSPZ ZMax® Single Stud Plate Tie is a prebent strap designed to connect single studs to either top or bottom plates. This versatile single-stud-plate connector helps to...
The Simpson Strong-Tie SSPZ ZMax® Single Stud Plate Tie is a prebent strap designed to connect single studs to either top or bottom plates. This versatile single-stud-plate connector helps to create a continuous load path in uplift resistance. The SSP features a top flange that allows the plate to attach securely to both sill plates and top plates. ZMax® coating provides extra corrosion resistance when used in more corrosive environments. Embossments feature provides strength at the...
The Simpson Strong-Tie VPA2.06 Variable Pitch Connector may be sloped in the field, offering a versatile solution for attaching 2" wide rafters to the top plate. It will adjust to accommodate slopes...
The Simpson Strong-Tie VPA2.06 Variable Pitch Connector may be sloped in the field, offering a versatile solution for attaching 2" wide rafters to the top plate. It will adjust to accommodate slopes between 3:12 and 12:12, making it a complement to the versatile LSSR Series Field-Adjustable Jack Hangers. This VPA series connectors eliminate the need for notched rafters, beveled top plates and toe nailing. Material: 18 Gauge Finish: Standard G90 Zinc Width: 2-1/16" Actual Joist Width: 2"...
The Simpson Strong-Tie A23Z ZMax® Framing Clips for various wood to wood connections at a 90° angle. ZMax® coating provides corrosion resistance when required. Material: 18 Gauge Finish:...
The Simpson Strong-Tie A23Z ZMax® Framing Clips for various wood to wood connections at a 90° angle. ZMax® coating provides corrosion resistance when required. Material: 18 Gauge Finish: ZMax® G-185 Coating Length: 2-3/4" Flange #1 (W1): 2" Flange #2 (W2): 1-1/2" Fasteners: (8) 10d x 1-1/2" Nails or(8) SD9112 Screws A23Z Information and Installation Instructions ZMax® Galvanized Coating Information ZMax® Coating is a thicker coating (galvanized per ASTM A653 with a G185...
The Simpson Strong-Tie A34SS Stainless Steel Framing Clips for wood to wood connections at a 90° angle. Stainless Steel material provides excellent corrosion resistance in highly corrosive...
The Simpson Strong-Tie A34SS Stainless Steel Framing Clips for wood to wood connections at a 90° angle. Stainless Steel material provides excellent corrosion resistance in highly corrosive environments. Length: 2-1/2" Finish: Type 316L Stainless Steel Flange Widths: 1-7/16" Fasteners: (8) 8d x 1-1/2" A34SS Information and Installation Instructions Type 316L Connector Stainless Steel Information Type 316L stainless steel is a nickel-chromium austenitic grade of stainless steel with 2-3%...
The Simpson Strong-Tie DSC5L-SDS3HDG Hot Dipped Galvanized Left Drag-Strut Connector transfers the diaphragm shear forces from the girder truss or beam to the shearwalls. It is quickly installed...
The Simpson Strong-Tie DSC5L-SDS3HDG Hot Dipped Galvanized Left Drag-Strut Connector transfers the diaphragm shear forces from the girder truss or beam to the shearwalls. It is quickly installed using 3" SDS screws that are included with the connector. The DSC5L-SDS3 series drag strut connectors requires 40% less fasteners than the DSC4L connector but gets 12% higher loads. Material: 3 gauge Finish: Hot Dipped Galvanized Dimensions: 21" (Length) x 3" (Flanges) Included Fasteners: (24) SDS 1/4"...
The Simpson Strong-Tie DSP Double Stud Plate Tie is a prebent strap designed to connect double studs to either top or bottom plates. This versatile double-stud-plate connector helps to create a...
The Simpson Strong-Tie DSP Double Stud Plate Tie is a prebent strap designed to connect double studs to either top or bottom plates. This versatile double-stud-plate connector helps to create a continuous load path in uplift resistance. The DSP features a top flange that allows the plate to attach securely to both sill plates and top plates. Embossments feature provides strength at the bend Can be installed before or after placement of wall Material: 18 Gauge Finish: Standard G90 Zinc Fastener...
Save by Purchasing 72 Box Special! The Simpson Strong-Tie DTC Double Slotted Roof Truss Clips are used for alignment control between a roof truss and nonbearing walls. The DTC has two 1-1/2" slots...
Save by Purchasing 72 Box Special! The Simpson Strong-Tie DTC Double Slotted Roof Truss Clips are used for alignment control between a roof truss and nonbearing walls. The DTC has two 1-1/2" slots that will permit the truss chord to move vertically when loads are applied to the roof. The double slot increases the allowable load values. Material: 18 Gauge Finish: Standard G90 Zinc Fasteners: (6) 8d Nails DTC Information and Installation Instructions Standard G90 Zinc Galvanized Coating...
Save by Purchasing a Pallet of 48 Boxes! The Simpson Strong-Tie H1AZ Zmax® Hurricane Tie provides a connection between the truss or rafter and the wall of the structure that helps resist wind...
Save by Purchasing a Pallet of 48 Boxes! The Simpson Strong-Tie H1AZ Zmax® Hurricane Tie provides a connection between the truss or rafter and the wall of the structure that helps resist wind and seismic forces. The H1A is designed for nominal 2x lumber. These U-shaped hurricane ties provide faster installation than using two single-sided ties. The embossments add stiffness in crucial areas for improved performance. Holds the rafter or truss on both sides for high lateral load resistance...
The Simpson Strong-Tie HGAM10KTA Hurricane Gusset Angle is designed to secure the bottom chord of a gable end truss or other framing member to masonry. The engineered gusset in the angle increases...
The Simpson Strong-Tie HGAM10KTA Hurricane Gusset Angle is designed to secure the bottom chord of a gable end truss or other framing member to masonry. The engineered gusset in the angle increases strength for lateral and uplift loads. This hurricane gusset angle installs easily with 1 1/2" Strong-Drive® SDS Heavy-Duty Connector screws and Titen Turbo™ masonry screws to concrete or masonry. Each Kit Includes: (10) HGAM Hurricane Gusset Angles (40) 1/4" x 1-1/2" SDS Screws and (40)...
The Simpson Strong-Tie LS50Z Skewable Reinforcing Angles with ZMax® Protection Coating are field adjustable from 0° to 135°. These clips come standard with a 45° bend. The LS...
The Simpson Strong-Tie LS50Z Skewable Reinforcing Angles with ZMax® Protection Coating are field adjustable from 0° to 135°. These clips come standard with a 45° bend. The LS Skewable clips can only be bent one time. Flanges are 2-1/4" wide. LS50Z Angles can use 10d .148" x 1-1/2" or longer nails depending on the application. Material: 18 Gauge Finish: ZMax® Coating Length: 4-7/8" Flange Widths: 2-1/4" x 2-1/4" Fasteners: (8) 10d x 1-1/2" Nails LS50Z Information and...